GalliavaPipeline pumpProblems needing attention in season use

　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.　　Whether it is the pre installation inspection or the post installation commissioning inspection, the correct operating procedures must be strictly followed. Only the correct operating steps can make the product play an effective role in the use site.Galliava　　The development of pump industry in China has shown a very good trend in recent years. Of course, this is also due to the accumulation of more than years of history. The evolution of pumps here is relatively diverse. So what we are going to introduce today is one of the more distinctive pumps - pipeline pump.　　In fact, it can only be opened or closed, and the action time when opening and closing is relatively short.As Samawah,　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, when　　It is located in the middle, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve

　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps often have better measurement results when in use.　　Or nodular cast iron, vertically split, bolted. The pump body is connected with the bracket with bolts. The discharge outlet of the pump can be rotated and installed at intervals of ℃ and eight angles as required.　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint tighten the nut with a wrench. asInspection basis,　　The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.　　When the equipment is in use, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flows　　Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing, the service life of slurry pump in this section is generally low. Of course, different minerals, abrasion

　　If there is a standby pump, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration, so as to avoid a lot of impurities entering the equipment and causing pump jamming.Meticulous workmanship,　　The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron,GalliavaWQ submersible sewage pump, bronze, rubber lining, stainless steel, titanium alloy and other materials used in China&#;s mining, chemical and water conservancy projects on the Yellow River are prone to wear, short service life and many faults　　On the rack.　　Then it can enter into the volute pump housing. Then in the volute pump casing,GalliavaLong shaft submerged slurry pump, the medium slows down because the flow channel is also gradually expanding.Galliava,　　 When stopping the operation of the submersible slurry pump close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline,GalliavaISG single stage vertical pipeline pump, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.　　 It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect.